Saturday, May 28, 2016

Time invested and budget: '64 Scotty Sportsman - from simple dream to economic reality

Purchased this cute '64 Scotty Sportsman from an Oceanside, CA motorcycle dealer for $900.
We purchased this little trailer almost 3.5 years ago, dreaming of a fairly easy fix and a resulting cool little trailer made in the same year I graduated high school (1964).

It's become more of a project that I ever dreamed; made all to easy to put off by our purchase of a cute little '58 Scotty Junior teardrop, a finished reproduction version, three summers ago. We have been across the US twice with the Scotty teardrop, up to Canada twice, and made dozens of shorter trips throughout the west.

With the aluminum skins and roof removed, the dry rot on the right side was quite extensive (was able to push what was left of the 1/2 plywood out by hand)! Yes, that right rear end was almost completely dry-rotted - most of damage due to roof seam leak. If you are ever perusing a trailer to purchase, take a hard look at the underside, and any patches on interior!
But, my spouse and two good friends have kept after me, and in recent months we're finally rebuilding the '64 Scotty. You'll see in the three previous posts how far we have come, and our current state (new floor down and finished, side up, beginning work on rebuilding the interior dinette and rear Gaucho/bed area - and installing the new cabinets made by my wood-working good friend, Tom Wilson).

I thought some of you might be interested in the "real budget" of both time and expense.

Grinding off the nailheads/removing the 200+ screw nails became a bit easier with a new Dremel tool.
Time invested: So far, I would estimate I have put in maybe 300 hours; my wife, 40: my pals Tom (the expert woodworker who rebuilt all three of the cabinets with only a bit of help from me) and Gary, another 100 hours or so.  When finished, I would estimate about 600 to 700 hours total.


Actual spending: It's noted below...

Purchased (item, supplier, cost):
’64 Scotty trailer, Southern Cal motorcycle dealer, $900
Dinette cushions, RVDoctorGeorge.com in Sacramento, $200
Roof and running lights, Amazon, about $40
Interior LED roof lights, Amazon, about $35
Roof vent, Amazon, $50
Hand pump for sink, Amazon, $56
Small corner silver fan, RVDoctorGeorge.com in Sacramento, $8
Three rolls butyl tape, Vintage Trailer, $20
New hinge for dining table, Vintage Trailer, $26
Door hinges, chevron door pulls, RVDoctorGeorge.com in Sacramento, $15
Used 30 amp power box, eBay, $20
Used Bargmann door handle, eBay, $90
Replacement Jalousie window for door installation, RVDoctorGeorge.com in Sacramento, $75.
Set of used Scotty hub caps, eBay, $75
Atwood two burner cooktop, Amazon, $145
Used Humphrey propane lamp, eBay, $45
Century Porta potty, Amazon: 11.75 inches tall, 16.25 inches deep, 13.5 inches wide, $90.
(2) 4X8 sheet of ¾” waterproof chipboard for floor, about $80.
(3) 4X10 sheets of ½” A-C marine plywood special ordered through Home Depot, about $130.
Misc. pine lumber, about $130.
Misc. paint, undercoating, about $70.
Misc. other stuff, about $100.
Total to date: $2,400.

Still to purchase:
(5) 4x8 by ¼ plywood for roof panels, additional pine 1X4s
Paint for the exterior of the trailer.
Wiring for the trailer
Two new trailer tires
Battery and inverter for the trailer

About $700 more to come.

Total, estimated when finished: approx. $3,100.


This is another '60s Scotty - we hope to look like this by late summer!
We think it will be a marvelous investment, loads of fun, and large enough in the interior that rainy days won't spoil an outing!

For more insight into this rebuild, connect with rebuilder Tim at tviall@msn.com, follow his Scotty-rebuild blog and check the web site for the National Serro Scotty Organization, nationalserroscotty.org, offering a huge resource to Scotty trailer owners and rebuilders!

Footnote: I am also the travel writer for the Stockton, CA, Record newspaper.  To read more about our travels, most of them with our Scotty teardrop, read Tim Viall's travel blog, follow him on Facebook or Twitter. Happy travels in your world!
Hopefully, we go from this stage, a few weeks ago, to the one above!



Wednesday, May 25, 2016

Sides going up on the new floor of our Scotty; new dinette, cabinet installation, Gaucho bed building next up!

Each of the two trailer sides is made from one full sheet of 4X10 1/2inch AC plywood and a partial 4X10 sheet, bonded with Tightbond waterproof glue and Simpson Strong-tie fasteners.  We let these joints cure for a couple days before cutting the actual side cuts (using the old aluminum skins as templates; and allowing for the future roof joists that would have to be covered by the side skins).

Here we have clamped the two sides together, and are belt sanding the edges so each side is a perfect twin to the other, and, that the top edges are exactly cut at 90 degrees.
Building the sides: as Scotty Sportsman rebuilders will know, the trailer body is 10 feet long, and less than 6 feet tall. We looked at rebuilds which used 4 x 8 sheets, glued and strapped vertically – we decided that 4x10 by 1/2 A-C plywood, glued then strapped horizontally, would make stronger sides with less joints. So we special ordered three sheets of 4 x 10 by 1/2 AC plywood through Home Depot, picking it up at the Boise Cascade yard a few miles south of town.

We glued the sheets together with Tightbond glue and Simpson Strongtie steel strapping, let cure for a day or two, then cut the two sides using the old aluminum trailer side panels as templates – (and carefully allowing for the roof beams). 

We then clamped the two sides together, and sanded the edges with a belt sander to make sure they were exactly the same size and the edges were a perfect 90°. You'll see the result in one of the pictures.

Using those aluminum side pieces as templates, we also scribed the two side windows and location for the door on the right side, as well as the cargo door on the rear, right side.

This is the new floor and sub-structure that we mounted the new sides to.
When we moved to mount the two sides to the trailer's new floor panels, we used the marks for the door location to line up with the step-down in the floor – as to the exact placement of the right side.

We mounted the right side first, aligning the scribed door opening with the floor's step-down area; then we mounted the left side to match the location of the right side.  We used two 1x3's as temporary bracing.
This shows detail and location of the left side, at front, mounted to the floor structure.  Note we have thoroughly undercoated both the new floor structure, and both sides of the new wall along the bottom foot or so - to prevent future water intrusion.
Then, we mounted the left side to match the right. Before mounting the two side panels, we thoroughly under coated the bottom foot of each panel, both sides, which was the area that the original panels had dry-rotted from moisture coming up from the bottom.

This photo shows the wheel well crimped, stapled and screwed to the new left side panel, and the serious undercoating applied to the rebuilt area.
Once the sides were mounted, it was easy to attach/crimp down the wheel wells, undercoat that area, and then thoroughly re-undercoat the bottom edge and outside edge of the two newly remounted side pieces.

You'll see we used a couple of 1x3s to temporarily stabilize the sides, as we begin work on the cabinets, dinette, rear gaucho/bed and installation of the cabinets.

When the two floor-mounted cabinets are installed, they also help stabilize the two sides.

Here is beginning of work on new dinette, with the new kitchen cabinet already installed.
From this point, we can now finished the front dinette, install the two new floor-mount cabinets and finish the rear Gaucho/bed area, then begin to install the roof panels. It won't be too long before this is looking like a Scotty again!

For more insight into this rebuild, connect with rebuilder Tim at his Email, follow his Scotty-rebuild blog and check the web site for the National Serro Scotty Organization, nationalserroscotty.org, offering a huge resource to Scotty trailer owners and rebuilders!

Footnote: I am also the travel writer for the Stockton, CA, Record newspaper.  To read more about our travels, most of them with our Scotty teardrop, read Tim Viall's travel blog, follow him on Facebook or Twitter. Happy travels in your world!

Thursday, May 19, 2016

Reconstructing the '64 Scotty Sportsman, rebuilding the floor

Scotty frame, sanded and undercoated.  Fortunately, the frame in very good shape for its 50 years!
Reconstructing the Scotty: In the last few months, we are back working on the Scotty.  I think I have acquired about every item needed for the rebuild over the past  several years, some through Amazon.com, like roof and running lights, new two burner range, new bar sink; some off eBay, like a Humphrey's gas lamp and sink hand-pump; and quite a bit on visits to a true old trailer resource in nearby Sacramento, RVDoctorGeorge.com (a company in Sacramento that scraps old and newer travel trailers, with about everything one might need that can't be found elsewhere). 

New Jalousie window, top, old one (missing most of its parts), below, and 12 volt fan; found both at
RVDoctorGeorge.com in Sacramento, an old trailer rebuilder's dream!
There, I found a good Jalousie window for the door for $75, almost a perfect fit, though rebuilding the door is yet to come. And, a set of four dinette cushions, the right color scheme and only $200, and other miscellaneous objects like knobs, hinges, a 12 volt fan and the like.

Save all those side, floor and roof panels and pieces; you will use some of them as
templates for your reconstructed Scotty trailer.
And, as mentioned in a previous post; we kept those old body panels, as templates.  Boy, happy I kept those old pieces, for they were/are very helpful in figuring out items as "just where to the two wheel wells get inserted into the floor", how were the front dinette and the rear gaucho bed constructed, and much more.  We also took extensive pictures of the "before trailer" and the trailer as we tore it apart - many times these have been helpful in beginning to put the new trailer body back together again!
The partially deconstructed trailer body; and, keep those side, roof and floor pieces as templates for the new trailer - they will come in awfully handy.  Also, take a lot of pictures of any tricky finish/construction details.

Working on installing the step-down floor, after installing all new redwood 2X2 joists.
New floor down, wheel wells installed, prior to putting down new linoleum.
Once we had the aluminum skins and roof panels off, it didn't take too long to knock the trailer box apart. Other than the right rear quarter panel, totally dry-rotted, saved the pieces for templates for future use. And, we took lots of pictures of the interior, and details of the demolition – as future reminders for rebuilding the Scotty.

New floor, and new linoleum, now installed.  Seems like we are headed in right direction!
Down to the floor – each side of the trailer is attached in 4-5 places, to the side trailer extensions, and in four places to the drop-down floor supports. Cut most of those off with my Dremel tool – then it was easy to pull the floor up and out. Again, saved the floor pieces as templates – this would be useful when it came time to locate the wheel well locations on the new floor.

We purchased 4 x 8 by three-quarter inch sheets of exterior marine chip board – believing this was more stable and weather impervious than three-quarter inch plywood. We used 2X2 inch red wood for the subfloor joists and edge pieces – thinking this was rot resistant. Once cut and bolted down, I  double-waterproofed from underneath with intent to make it weather-impervious. Will probably hit the undercoating again, once the entire body, aluminum sides and trim is finished. Best of all, in the West, we hardly ever camp in nasty weather, so the trailer, seldom wet and garaged when not used, should easily last another 50 years!

We found a nice linoleum pattern at Home Depot, with a subtle pattern, and in a few days had it cut and glued down. Future challenge will be to find new molding trim – but this can wait till later Will probably check out RVDrGeorge.com in Sacramento.

The three new cabinets constructed by friend Tom Wilson, with a bit of help from me.  We trimmed 6" width off both floor mount cabinets, so we can add 6" width to the gaucho bed in the rear of the trailer!
In the meantime, my buddy Tom Wilson, with only a little help from me, has remanufactured the three cabinets. With both the floor-mounted kitchen cabinet, and the wardrobe on the other side – we trimmed 6 inches off the width – with intention to make the bed 6 inches wider in the back (that will make the rear gaucho, when made into a bed, almost 55" in width; yay!).

Commensurately, the overhead cabinet was remanufactured, 6 inches narrower than the original. However, a new two-burner gas stove and oval bar sink (Amazon purchases) will both fit into the new kitchen cabinet – when we get to that point. In each case, the new cabinets for quality man, much better than a foot out – thanks to Tom's skills and experience.

Here, the two new sides were made from two pieces of 4X10' 1/2" marine plywood, special ordered from Boise Cascade through Home Depot.  We joined them horizontally, with Tightbond glue and steel ties.  Next step...to install the sides!
Next post will cover the installation of the sides and next steps to finishing the trailer box!  Already starting to think of the exterior color scheme (white base, Scotty Aqua blue and some Ford Ruby Red to match our 2013 Ford Escape tow vehicle)!

For more insight into this rebuild, connect with rebuilder Tim at his Email here, follow his Scotty-rebuild blog and check the web site for the National Serro Scotty Organization, nationalserroscotty.org, offering a huge resource to Scotty trailer owners and rebuilders!

Footnote: I am also the travel writer for the Stockton, CA, Record newspaper.  To read more about our travels, most of them with our Scotty teardrop, read Tim Viall's travel blog, follow him on Facebook or Twitter. Happy travels in your world!

Sunday, May 15, 2016

Back on the Scotty project; deconstructing a trailer with lots of dry rot!

Our '64 Scotty, after purchase in Oceanside in 2012.
OK, I'm going for the world record in time delays, over four years, in rebuilding a '64 Scotty Sportsman!

This view, under the gaucho bed, showing daylight, portended considerable dry rot on lower rear trailer body edge.
For those of you not up to the latest – I bought the '64 Scotty from a motorcycle dealer in Oceanside, California, in 2012, for $900. At the time, I knew it had dry rot problems and would need a certain amount of rebuild – but not quite how much. But, it was complete, original and had all the original inside features, even if in rough shape.

Our '58 Scotty Junior teardrop (reproduction by a talented West Virginia shop teacher) in Harper's Ferry, shortly after we picked it up on a planned trip to bicycle-tour the Gettysburg battlefield and the C&O Canal.
And, shortly there after, we had the good fortune to find '58 Scotty Junior teardrop (a reproduction model, constructed by Tom Scott, a West Virginia shop teacher) for sale, in West Virginia, just before a planned trip to Gettysburg for a bike tour of the battlefield and the C&O Canal. So, we bought the teardrop, picked it up and have used it extensively in the last three years. It's presence made it all too easy to think "next week, I'll start on the '64".  Weeks became months, then years...

Able friend Tom Wilson, with newly constructed kitchen cabinet, kept
after me (not-too-gentle prodding!) and helped greatly in recent months!
That made it relatively easy for me to delay work on the '64 Sportsman. Fortunately, I have both a good friend – Tom, a quality woodworker - and a spouse who have kept after me. So, in the last five months, we have resumed work on the Scotty.

This shot shows the left, front side, with aluminum skin removed, showing dry rot beneath the molding.
To get underway, one first has to remove the aluminum skins and roof panels. It's a bit daunting to remove all the aluminum screw nails that hold this trailer together, starting with about 250 that attach the trim on the side moldings.

Left rear, behind wheel well, showing dry-rotted side piece and edge of floor.
But, with a newly purchased Dremel tool, I ground off most of the nailheads and removed the trim. With help from friends Tom, Gary and my wife, we removed the aluminum roof pieces and side pieces. From there, the need to replace both the floor and the body became all too evident.

Revealing picture of the right side - yes, the entire area in rear of trailer, from 10" behind door to rear, was dry rotted - only the aluminum skin, and a piece of plywood paneling a previous owner nailed over it, held the trailer side together!
Most of the right rear side panels were totally dry rotted – the aluminum skin was holding it together. Plenty of dry rot around both side windows, the front window and along the roof seams meant the need to replace both sides in the front and rear. With the floor, dry rot had ruined the areas around both wheel wells. Hence, our decision was made to totally rebuild the trailer.

Trailer with the rear and the right side torn off.
From there, deconstructing the trailer body and floor was relatively easy. In each case, we saved the deconstructed pieces as templates for the future rebuild. This would become prescient soon after.
In the series of pictures, you'll see the trailer with the skins removed, and the process of tearing it down, all the way to a bare frame.  From there, sand the frame (in good condition), waterproof the bare metal, and begin figuring the list of plywood and additional items necessary to put the new trailer together.

Here, the floor remains after tearing off the trailer body; below, author Tim sanding the trailer frame..
Watch for the next installment, where I'll share insight on rebuilding the floor, sides and cabinets.

For more insight into this rebuild, connect with rebuilder Tim at tviall@msn.com, follow his blog at serroscotty64.blogspot.com and check the web site for the National Serro Scotty Organization, nationalserroscotty.org, offering a huge resource to Scotty trailer owners and rebuilders!

Thanks for reading!